Electric Single Heater Cartridge by Factory Direct Sale

We have great advantages and influence in talents, resources, network, scale and experience in production of hot tub heater element resistance, 3d printer cartridge heater, ceramic bobbin heater, and become one of the enterprises with high competitiveness. We are committed to improve and complete the quality system continually, in order to build up the consciousness of products of the best quality. Our company adheres to the tenet of 'survive by quality, develop by reputation', and always implement the 'integrity' policy to meet customer needs. We always insist that innovation is the only way for an enterprise to break through and expand its development space.

As a very widely used heater,Heater Cartridge Construction permits higher watt densities. Standard SS316 and optional Incoloy 800 sheath provide good thermal conductivity and resistance to corrosion and scaling. Heater Cartridge

Features: Heater Cartridge
● Max Sheath Temperature 800°C (Depend of sheath material)
● 6V ~ 480V Voltages
● Dia.3mm to 30mm
● High Purity MGO
● Glass filament blanket
● 12” standard lead wire length
● Crimped On Lead & Swaged In Lead
● Custom design or built in thermocouples are available

Application:
● Semiconductor chamber heating
● Semiconductor wire & die bonding
● Humidity Control
● Patient comfort heating used in medical devices
● Mold die and platen heating
● Seal bars used in packaging equipment
● Test sample heating in gas chromatography equipment

Each Heater cartridge is carefully designed

Construction of a cartridge heater may be divided in 6 main parts:

1.Heating coil

The heating coil is the actual resistance which is where the electrical load occurs. The most common type of metal alloy used for this purpose is a nickel-chromium mixture, also known as nichrome. The nichrome wire is wound around a ceramic core, and the number of spirals per inch vary according to the requested watt density. Potential from an alternating current source, which can either be 2 phase or 3 phase, flows through the coiled nichrome wire, heating up the wire, which in turn, heats the cartridge heater sheath.

2.Insulation

Insulation is used to prevent the nichrome coil contacting the sheath, an event that would ground the resistance and could produce a catastrophic short-circuit, resulting in a melted sheath and a major equipment failure. Damage can be mitigated by installing a ground fault interrupting circuit. To prevent the coil from touching the sheath, the coil is inserted into the sheath, and immediately filled with magnesium oxide (MgO). To ensure the MgO fills the empty space between the sheath and the coil, the cartridge heater is filled under vibration.

3.Sheath

The sheath is the part of the cartridge heater which makes contact with the material or substance to be heated. Several metal alloys are used, depending on the type of application, such as highly acidic or corrosive environments. The most common types of sheaths are 304 stainless steel, 316 stainless steel, and incoloy 800. Incoloy has the highest temperature rating, and is considered a superalloy.

4.Sealing

After the cartridge heater has been filled with MgO, a seal is applied to the open end of the cartridge heater (where the nichrome coil was introduced). This prevents the coil and the MgO from coming out, as well as preventing contaminants such as plastic debris, air, or moisture from entering the heater.

5.Termination

Since cartridge heaters are installed in a wide variety of machines, manufacturers must design the heaters to meet certain clearances.[7] [dead link] The cartridge heaters might be terminated with the leads coming out straight, or in a right angle. Also, manufacturers must be careful that the leads are not exposed to temperatures higher than the maximum rating for the lead wire. In order to prevent lead wire damage from temperature, movement or contamination, the lead wire can be protected with a metal conduit, braided metal or silicone sleeves.

6.Lead wire type
Depending on the clearance and the design of the machine where the cartridge heater will be inserted, the type of wire used will vary. Fiberglass is the commonly used for cartridge heaters and other high-temperature applications, such as automotive wiring harnesses and industrial equipment. Other variants used are silicone impregnated fiberglass and silicone rubber.

Innovative, durable and cost-efficient products have secured us a position as a leading global manufacturer of Electric Single Heater Cartridge by Factory Direct Sale. We adopt one-stop professional team management. We will further enhance the influence of our company and strive to rely on our unique advantages to establish a long-term foothold in the international market.